GW Instek PPH-1503

Programowalny precyzyjny zasilacz DC PPH-1503 USB / LAN /GPIB

More info
Data sheet
Download
Accessories

Features

Dual Range Output (0~15V/0~3A) or (0~9V/0~5A)
3.5 Inch TFT LCD Display
Constant Voltage and Constant Current Operation
Built-in DVM Measurement Function
High Measurement REsolution (1mV/0.1mA for 5A Range);(1mV/0.1uA for
5mA Range)
EXternal Relay Control Output On/Off
Sink Current Capability (Maximum:2A)
Digital Panel Control
Selectable Output and Input (DVM) Ports From Front or Rear Panel
Key Lock Function
5 Sets of Preset Memory Including Power Output ON/OFF States
High Speed Transient Recovery Time(<40us within 100mV ; <80us within
20mV)
OVP/OCP/OTP Protection to Prevent DUT Damage
Standard Multiple Interfaces: USB / LAN /GPIB
Labview Driver and PC Remote Control Software

DC GENERAL	MEASUREMENT TIME CHOICES	0.01 ~ 10PLC¹,0.01PLC/step
	AVERAGE READINGS	1~10
	TYPICAL READING TIME^2,3	31ms
DC VOLTAGE OUTPUT (23℃±5℃)	OUTPUT VOLTAGE	0~15V
	OUTPUT ACCURACY	± (0.05%+10mV)
	PROGRAMMING RESOLUTION	2.5mV
	READBACK ACCURACY³	± (0.05%+3mV)
	READBACK RESOLUTION	1mV
	OUTPUT VOLTAGE RISING TIME	0.15ms (10% ~ 90%)
	OUTPUT VOLTAGE FALLING TIME	0.65ms (90% ~ 10%)
	LOAD REGULATION	0.01%+2mV
	LINE REGULATION	0.5mV
	STABILITY⁴	0.01%+0.5mV
	RECOVERY TIME(1000%LOAD CHANGE)	<40us (<100mV) <80us (<20mV)
	RIPPLE AND NOISE⁵	1mV rms(0~1MHz) 8mVpp(20Hz~ 20MHz)
DC CURRENT (23℃±5℃)	OUTPUT CURRENT	0 ~ 5A (0 ~ 9V) 0 ~ 3A (9 ~ 15V)
	SOURCE COMPLIANCE ACCURACY	±(0.16%+5mA)
	PROGRAMMED SOURCE RESOLUTION	1.25mA
	READBACK ACCURACY³	5A range: ±(0.2%+400uA) 5mA range: ±(0.2%+1uA)
	READBACK RESOLUTION	5A range: 100uA 5mA range: 0.1uA
	CURRENT SINK CAPACITY	0 ~ 5V: 2A 5 ~ 15V:(2A derate 0.1A)/V
	LOAD REGULATION	0.01%+1mA
	LINE REGULATION	0.5mA
	STABILITY⁴	0.01%+50uA
DVM	INPUT VOLTAGE RANGE	0 ~ 20VDC
	INPUT IMPEDANCE	10Ω
	MAXIMUM INPUT VOLTAGE	-3V, +22V
	READING ACCURACY³	± (0.05%+3mV)
	READING RESOLUTION	1mV
PULSE CURRENT MEASUREMENT	TRIGGER LEVEL	5mA ~ 5A, 5mA/step
	HIGH TIME/LOW TIME/AVERAGE TIME	33.3us to 833ms, 33.3us/step
	TRIGGER DELAY	0 ~ 100ms,10us/steps
	AVERAGE READINGS	1 ~ 100
	LONG INTEGRATION PULSE TIMEOUT	1S ~ 63S
	LONG INTEGRATION MEASUREMENT TIME	850ms(60Hz)/840ms(50Hz) ~ 60s,or AUTO time 16.7ms/steps(60Hz), 20ms/steps(50Hz)
	LONG INTEGRATION TRIGGER MODE	Rising, Falling, Neither
OVP	OVP RANGE	OFF,ON (0 ~ 15.2V)
	RESOLUTION	10mV
	ACCURACY	50mV
Others	PROGRAMMING	IEEE-488.2(SCPI)
	USER_DEFINABLE POWER_UP STATES	5 sets
	REAR PANEL CONNECTOR	8Pin:output4, sense2, DVM*2
	TEMPERATURE COEFFICIENT	0.1* specification/ ˚C
	POWER CONSUMPTION	150VA
	REMOTE/LOCATION CONNECTOR	USB/GPIB/LAN
	RELAY CONTROL CONNECTOR	150mA/15V 5Voutput, 100mA
Insulation	Chassis and Terminal	20MΩ or above (DC 500V)
	Chassis and AC cord	30MΩ or above (DC 500V)
Operation Environment		Indoor use, Altitude: ≤ 2000m Ambient temperature: 0 ~ 40°C Relative humidity: ≤ 80% Installation category: II, Pollution degree: 2
STORAGE Environment		TEMPERATURE: -20˚C ~ 70˚C HUMIDITY: < 80%
INPUT POWER		90-264VAC, 50/60Hz⁶
Accessories		CD 8cmUser manual x1, Quick Start manual x1 Test lead GTL-117 x 1, GTL-203A x 1, GTL-204A x 1
Dimensions		222 (W) x 86 (H) x 363 (D) mm
Weight		Approx. 4.2kg

Remarks		PLC=PowerLineCycle, 1PLC = 16.7ms for 60Hz operation, 20ms for 50Hz operation; Display OFF, Speed includes measirement and binary data transfer out of GPIB; PLC=1; STABILITY:Following 15 minute warm-up, the change in output over 8 hours under ambient temperature, constant load, and line operating conditions; The ground ring of the probe is pressed directly against the output ground of the power supply and the tip is in contact with the output voltage pin. Auto detected at power-up;